8 best fuel transfer systems

• Fuel Loss Prevention System will Buzz Automatically to prevent Fuel Loss
• Flow Rate of 9.6 Quarts per Minute or 2.4 GPM, Requires 2pk of AA Batteries (NOT INCLUDED)
• Siphon a various liquids like any non-corrosive liquid, gas, diesel kerosene and water (Not for drinking)
• Suction Tube Length to 15.5 inches to reach every last bit of fuel
• CSA Certified under UL Standards. This product was tested by CSA per an agreement with UL, and is certified for use in both Canada and the US according to applicable Canadian and US standards

User questions & answers

Question:	Will it lift gas from ground into 3/4 pickup
Answer:	We have ours on a transfer fuel tank, but because we have a pump it is not adequate venting and the sides of the tank suck in. We take the cap off to pump. If you have a gravity flow tank it may work just fine.
Question:	Is this safe to use with E
Answer:	We have a Transfer Flow auxiliary fuel tank and it fit great. Not sure if the tanks are the same size.
Question:	Why no auto-stop with the Trep01 pump
Answer:	I don’t thinks so This fits a 2inch NPT thread However there is a locking cap for a freightliner tank Measure to confirm
Question:	Is it possible to shorten the suction tube
Answer:	Measure the outlet to see if it's there same size

Product features

Battery Powered Liquid Transfer Pump

Applicable Liquids: Any non-corrosive liquids such as gas, diesel, and water (DO NOT use for drinking water)

Delivery Volume: 9 Liters per Minute

Power: Two "AA" Batteries (Not Included)

Suction Tube Length: 15.5 inch

Suction Tube Diameter: 1.3 inch

Discharge Tube Length: 24 inch

• Built in Auto-Stop to prevent loss of fuel
• Fuel Loss Prevention System: Automatic sensing pump / Buzzer Warning
• Works great with Kerosene heaters
• Makes refueling generators, lawn equipment, farm equipment simple, lifting heavy gas can's to refuel your equipment will be a thing of the past

Operation Instructions:

1. Insert Two "AA" Size Batteries (Not Included)
2. Insert Suction Tube into sending Container (Gas Can or Container with Fuel)
3. Clip discharge hose to receiving end
4. Flip Power Switch to Start
5. To Stop Flow, Wait for Auto-Sensor or flip power Switch Off

• GASOLINE OR DIESEL 12 volt electric, dry start & transfer fuel from airplanes, boats, RV's, ATV's, many cars & equipment - An excellent tool for preppers!
• Large weather resistant air-tight carrying case 12" x 14" x 5" - carry fume free
• Case mounted pump moves 1.2 gallons per minute, 70 gl. per hr. - high lift pump 24'
• 8’ lines of 3/8” USA fuel line, 7' 3/8 line, 12V auto pwr plug, LED indicator, fuse
• 15' air activated safety switch - Look for GASOLINE SPECIFIC when comparing. Focus on Safety.

User questions & answers

Question:	Does this require a separate battery, or will it hook to a 12v car battery
Answer:	Mine is 4 ft away no problems
Question:	What is the amperage draw on this unit and does it have a run time limit
Answer:	I guess that's the way they come
Question:	how long is the 12v cable
Answer:	no
Question:	How long of a hose can be attached to this and still have it function properly
Answer:	I used alligator clamps

Product features

GasTapper 12 Volt Max Fuel Transfer Pump

The GasTapper 12V Max Fuel Transfer Pump comes with useful features to help you get the job done. It works on many cars*, boats, RVs, UTVs, as well as a variety of other fuel vessels.

Portability

It's great to always be prepared for the unexpected. That's why we house our transfer pumps in top of the line fume & weather proof cases that are both portable & durable.

Safety

We want our customers to have ease of mind and the ability to get a job done cleanly and effectively. Now you can transfer fuel without spilling or tasting it!

Patented Hose Man Clip & USA Made Fuel Line

• Secure the Hose to a Variety of Containers to Prevent Spillage
• Model Includes 2 Clips for both the Input and Output Sides
• USA Made and Certified Fuel Grade Hose

Max Case

• Weather Proof
• Fume Proof
• Lightweight

12V Fuel Pump

• German Designed Fuel Pump
• Capable of Pumping One Gallon Per Minute
• Durable & Efficient
• Gasoline & Diesel Specific

Air Safety Switch

• 15' Safety Switch
• Acts as Remote Control for Full Control

Product description

PREVENTS FUEL THEFT!

The New Designed FSS-754 VersaLock security cap is a quick and inexpensive way of safeguarding costly fuel and oil from theft, tampering and vandalism. It is designed for use on mobile fuel transfer tanks as well as above ground commercial gas and distillate tanks. The FSS-754 uses built in valves to equalize the pressure and vacuum. The FSS 754 is different from any other cap on the market today. It is designed with Spinsecure's patented "free-spinning" technology. When the cap is in the secure mode the cap will free spin making it virtually impossible to remove.

KEY BENEFITS:

• Includes 2 Keys
• Made From Hard Non Ferrous Alloy
• Weatherproof
• Prevents Theft
• Saves Money

Fits all 2" standard male and female threads or can be used with a 750-200 adapter (not included) to convert to a 2" standard female thread. Quick Fill and BSP threads also available.

Flow Security Systems manufacturing plant is located in Camarillo California. It is a vertically oriented company with an in-house team of engineers, tool-makers, salesmen and marketing personnel. Flow Security Systems goal is to deliver excellent service and products based on years of dependable service and reliable product.

Are you protecting your fuel, chemicals and water from theft? Purchase one of our locking devices today to help prevent unauthorized use, tampering and theft and keep your fuel costs down!

• PREVENT UNAUTHORIZED USE: The Flow Security Systems PRE-VENT Fuel Cap is a quick and inexpensive way to safeguard costly fuel and oil from theft, tampering, siphoning and vandalism. The Versa Lock utilizes the patented free spinning design, perfect for all business owners who want to secure their transfer fuel tanks.
• MULTIPLE USE: The FFS 754 is designed for use on mobile fuel transfer tanks as well as above ground commercial gas and distillate tanks. The VersaLock has weather proof self-closing latch covering the face of the lock to prevent dust, dirt, debris and moisture from entering the lock.
• KEYED DIFFERENTLY OR THE SAME: The Versa Lock can be keyed alike so that multiple fuel caps can be secured with the convenience of having only one key. Perfect for those who have multiple transfer tanks and don't have to carry different keys for each tank. But if you prefer a different key, that option is also available. The VersaLock can also be keyed differently so that each fuel cap can have its own unique key, providing added security for your tank.
• BUILT IN VALVE: The FSS-754 uses built in valves to equalize the pressure and vacuum. Pressure vent valve allows pressure relief valve to open at 1.5 Lbs and vacuum release to open at 1.5 OZ. This heavy duty lock is make from hard non ferrous alloy and fits standard 2 inch male thread.
• PATENTED DESIGN: The FSS 754 is different from any other cap on the market today. It is designed with our patented "free-spinning" technology. When the cap is in the secure mode the cap will free spin making it virtually impossible to remove.

User questions & answers

Question:	Will this cap fit a transfer flow tank
Answer:	length: 35,8 width: 23,6 height: 24,4 in
Question:	Work on a Transfer Flow auxiliary fuel tank
Answer:	We sell the nozzle meter separately but, at this moment, we don't have it in stock. If you want, I'll let you know when we have it again in approx 45 days. Regards.
Question:	Is this product fit on a freightliner m2 straight truck
Answer:	Manual states something around 25-30 amps. 12V.
Question:	Can i used for isuzu 2003 frr box truck
Answer:	I don’t know for sure but I think the company that purchased these do you sell one.I haven’t bought a filter kit yet I just got mine I actually haven’t even put fuel in it yet

Product description

The FR1204H is a 12V 15 GPM fuel transfer pump that comes as a pump only model and comes with a 3/4" elbow, 5’ 12-gauge ground wire, and a 18’ 12 gauge 2-wire battery cable (3/4" outlet). It can be used to pump gasoline, diesel, kerosene, ethanol blends up to 15%, methanol blends up to 15%, and bio-diesel up to B20. The previous FR1204G model has been updated to the FR1204H model. With a removable junction box, the product is now easier to install. The performance specifications of the product did not change.

• Durable cast iron pump housing built to withstand the wear and tear of rough operating environments
• Removable junction box allows for easier installation
• Thermal overload protection prevents motor from overheating during abnormal usage
• Pump is capable of pumping fluid out of an 8' deep storage tank at sea level
• Rugged switch lever is designed to endure heavy abuse

User questions & answers

Question:	I would like to buy this package but can I get the green handle automatic nozzle instead
Answer:	I don't believe it does. A separate wire to ground can be attached and taped to the outside of the hose if you wish.
Question:	Which Fill-Rite pump is suitable for aviation fuel? (avgas
Answer:	I believe the hoses are pre manufactured to standard lengths.
Question:	can the pump run with the nozzle closed without damaging the pump
Answer:	Make your own home Depot has all the parts.
Question:	Can someone tell me for sure if this particular pump carries the 2 year warranty expressed here
Answer:	The fittings are 3/4 pipe so I guess the i.d of the hose would be close to that

Product features

Rotary Vane

Rotary vane technology is a positive displacement (fixed volume) pump design that utilizes an offset rotor with sliding vanes that rotates on a motor shaft inside the pump. The vanes move outward against the pump cavity to form individual chambers (positive displacement). Fuel enters into the pump cavity through the inlet port on the rotor side where the vanes are fully extended. As the rotor turns, the vanes collapse inward creating the pressure that forces the fuel into the discharge port and through the hose.

Advantages of rotary vane technology…..

• Increased suction lift
• No performance loss due to vane wear
• Self-priming ability
• Easy maintenance
• Consistent performance

Suction Lift

The maximum suction lift rating refers to the maximum vertical distance that a pump can lift fuel out of a tank. On rotary vane pumps, suction lift is created due to the offset of the rotor in the pump cavity, which increases the volume in the chamber between the vanes, thus lowering the pressure on the pump’s inlet. Atmospheric pressure, which is now greater than the inlet pressure in the pump, moves the fuel from the tank to the pump cavity (self-priming).

Suction lift is determined by the pump specifications, the type of fuel, and the altitude of the location where the pump is installed. Higher altitudes reduce the suction lift of a pump due to the reduced atmospheric pressure.

To achieve maximum suction lift, the inlet plumbing should be as straight as possible with no elbows or bends in the line. Accessories, such as filters, should not be installed on the inlet side of the pump. Valves should be set with minimum spring pressure and must contain a pressure relief valve.

Discharge Pressure

Discharge pressure refers to the systems pressure while dispensing. It effects flow-rate based on the pump’s design - the lower the discharge pressure, the higher the flow-rate.

Variables that increase discharge pressure/decrease flow-rate:

• Adding accessories (filters, measuring devices, swivels, etc…)
• Changing accessories (increasing the length or decreasing diameter of hose)
• Dispensing fuel above the pump (the higher the discharge point is above the pump the lower flow-rate)p
• Pumping higher viscosity fluids (Fill-Rite pumps are designed to pump at a viscosity no greater than kerosene)

To lower discharge pressure/increase flow-rate, remove or limit restrictions. Examples include, moving from a 10 micron filter to 30 micron filter, changing from a 800 series to a 900 series or TT10 series, limiting the use of elbows in system design, or increasing the diameter of your discharge hose/pipe.

KIT120RKG

Primary pump repair kit for 1200 series pumps.

KIT120ARM

Motor repair kit for 1200 series pumps.

KIT120BD

Bio-diesel conversion kit for 1200 series pumps.

KIT120NB

Nozzle boot kit for 1200 series pumps.

NX25 Series Fuel Transfer Pump

Nextec Intelligence is an exclusive array of design advancements, technologies and user functionalities that take pump performance to unprecedented levels. Intelligent Tones inform when attention is needed. A variable speed motor automatically adjusts for peak performance with improved suction lift. More compact, lighter, and less amp draw—it sets a new standard for efficiency.

Simple features, such as the lower pump weight, makes this pump great for mobile applications or on the less sturdy aluminum fuel tanks. Other convenient features, like a removable power cord or an auto power down function (after 20 minutes of inactivity), are benefits other pumps just don't offer. Whether the application is 12V, 24V, 115V, or 230V this premium offering from Fill-Rite consistently gets the job done.

With Nextec, the future of fuel transfer is here.

Product description

115V, heavy duty, fill Rite pump, explosion proof motor with ball bearings & thermal overload protection, features integral check valve & strainer, hose has static wire, pad lock able, provides safe, efficient transfer of diesel, gasoline, kerosene, mineral spirits, Stoddard solvent, white spirits & Heptane, UL, cul & CSA listed. This product adds a great value. Product is highly durable and very easy to use. This product is manufactured in United States.

• 1/3 hp, 115V, 5.5 amp motor
• 20 gpm flow capacity at 1,725 rpm with 8' maximum lift
• Cast iron housing with buna-n mechanical seal and O-ring for durability
• Suitable for transfer of gasoline, diesel, B20, E-15, kerosene, and mineral spirits
• UL and CUL listed

User questions & answers

Question:	Can you install it to a 80 foot hose and expect it to work properly
Answer:	Please be noted the suction tube is 2pcs extensible pipe, it could be adjusted from 26”to 36”.
Question:	How many gpm
Answer:	Hello Rachel, Thank you for contacting us regarding. Yes, this pump is available for gasoline.
Question:	Do you supply or sell suction pipes for these pumps
Answer:	mine was for diesel fuel, not sure if it worked for gas also.
Question:	IS THIS PUMP FOR GASOLINE
Answer:	Why would you want to ,as I connected it directly to a gas container made from steel purchase from Northern tool No need for a water filter. It could be done just need to pump it between gas suction and spout
Question:	How much height does this add to a 55 gallon drum? A standard drum is 33.5 inches (851 mm) high and I am trying to choose a minished to store this in
Answer:	Bottom diameter is about 1.8“
Question:	Can I use this transfer pump to remove gasoline from a Plastic 55 gal. drum
Answer:	i think the dimensions are listed in the ad. i do like these a lot and work well
Question:	Is this a diesel pump available in a gasoline safe version, or is this the gasoline version
Answer:	The diameter of the ashtray is 4.7 inches. Let us know if we can assist further!
Question:	Can I use an in line water filter
Answer:	No

Product features

Fuelworks 10305708A DC 12V 15GPM Fuel Transfer Pump Kit w/14' Hose, Extensible Suction Tube & Manual Nozzle

In need of a strong & reliable transfer pump that can provide volume transfers for short or long distance applications? You need the right equipment to get the job done & our Heavy Duty Fuelworks Transfer Pump kits are the answer!

We can supply the demand for your fuel applications with our AC/DC Fuels Pumps, Nitrile/Viton Pneumatic Double Diaphragm Pumps or our specialized UREA/DEF Electric Fuel Transfer Pump.

We know fuels & what works, so we designed equipment to meet your Fuelworks needs.

Professional Specifications

Class 1 Division 1 Group D T4 Explosion Proof Pump

• Pump Type: Self-Priming, Volumetric, Rotary Vane equipped with by-pass valve
• Motor Type / Flow Rate: Positive Displacement Brush / 15GPM / 57LPM
• Current / Voltage / Power (Wattage) / Max Amperage (AMP): DC 12V 180W 22A
• Inlet / Outlet // Power Supply: Tank Adapter Male 2" / Female 1" // 16ft./5m Power Cable
• Rotations Per Minute (RPM): 2400 RPM
• Temperature: Min -20°C/Max +40°C (-4°F /max 104°F)
• Relative Humidity: Max 90%
• Noise Level: 80dB_ @ 1 meter

(Red Sleeve/Auto-Nozzle not included, can be purchased separately)

Quality Performance

Our Pumps go through rigorous testing with suitable fluids allowed by design, indicating high quality performance by ISO 9001:2008 standards (Cert# 16092009)

• This pump is suitable for flammable liquids like: Gasoline, Diesel Kerosene & Mineral Spirits.
• Recommended Duty Cycle: 30 minutes intervals.
• Recommended Duty Cycle Cool Down: Each 30 minute cycle should always be followed by a 30 minute power off cooling phase.
• This product is not suited for fluids of human consumption or fluids containing water, Nor aircraft applications.
• Do Not Run Dry For More Than 30 Seconds

Reliable & Versatile

The Explosion Proof Fuel Transfer Pump is designed for tank or barrel mounting applications to dispense acceptable flammable liquids.

• Safe mechanical seal structure & Heavy Duty Cast Iron Pump Chamber.
• Thermal Protected
• Bypass Valve
• Filter Screen at Inlet
• *Note: Use PTFE tape on ALL pipe threads when assembling.

Brush Motors are Low tension with intermittent cycle, closed type in protection>

Kit Essentials & Specs

Lockable Nozzle Holder, Extensible Suction Tube, Delivery Hose, Tank/Barrel Mountable 2" Bung Adapter is all included.

• Nozzle Cast Type / Model / Inlet: Aluminum / Manual / 1"
• Hose I.D. / Length Type / Max Pressure: 3/4" / 14ft.(4.2m) Anti-Static Delivery Hose (wire included) / 300PSI / 20BAR
• Strain relieving spring on hose ends.
• Spout Diameter / Inlet / Flow Rate: 15/16" / 3-26GPM / 10-100LPM
• Extensible Suction Tube: Extends from 26" to 36" in length. Cartridge Filter @ 30 Micron.

Rotary Vane

Rotary vane technology is a positive displacement (fixed volume) pump design that utilizes an offset rotor with sliding vanes that rotates on a motor shaft inside the pump. The vanes move outward against the pump cavity to form individual chambers (positive displacement). Fuel enters into the pump cavity through the inlet port on the rotor side where the vanes are fully extended. As the rotor turns, the vanes collapse inward creating the pressure that forces the fuel into the discharge port and through the hose.

Advantages of rotary vane technology…..

• Increased suction lift
• No performance loss due to vane wear
• Self-priming ability
• Easy maintenance
• Consistent performance

Suction Lift

The maximum suction lift rating refers to the maximum vertical distance that a pump can lift fuel out of a tank. On rotary vane pumps, suction lift is created due to the offset of the rotor in the pump cavity, which increases the volume in the chamber between the vanes, thus lowering the pressure on the pump’s inlet. Atmospheric pressure, which is now greater than the inlet pressure in the pump, moves the fuel from the tank to the pump cavity (self-priming).

Suction lift is determined by the pump specifications, the type of fuel, and the altitude of the location where the pump is installed. Higher altitudes reduce the suction lift of a pump due to the reduced atmospheric pressure.

To achieve maximum suction lift, the inlet plumbing should be as straight as possible with no elbows or bends in the line. Accessories, such as filters, should not be installed on the inlet side of the pump. Valves should be set with minimum spring pressure and must contain a pressure relief valve.

Discharge Pressure

Discharge pressure refers to the systems pressure while dispensing. It effects flow-rate based on the pump’s design - the lower the discharge pressure, the higher the flow-rate.

Variables that increase discharge pressure/decrease flow-rate:

• Adding accessories (filters, measuring devices, swivels, etc…)
• Changing accessories (increasing the length or decreasing diameter of hose)
• Dispensing fuel above the pump (the higher the discharge point is above the pump the lower flow-rate)
• Pumping higher viscosity fluids (Fill-Rite pumps are designed to pump at a viscosity no greater than kerosene)

To lower discharge pressure/increase flow-rate, remove or limit restrictions. Examples include, moving from a 10 micron filter to 30 micron filter, changing from a 800 series to a 900 series or TT10 series, limiting the use of elbows in system design, or increasing the diameter of your discharge hose/pipe.

700KTF2659

Primary overhaul kit for 700 series pumps.

KIT700AS

Anti-siphon kit for 700 series pumps.

KIT700MA

Meter flange assembly for connecting an 800 series meter to a 700 series pump.

KIT900PF

Meter flange assembly for connecting an 900 series meter to a 700 series pump.

Digital Inline Turbine Meters From Fill-Rite

Accurate to 1%, this turbine meter sets the standard for accuracy, ease of use and safety. Compatible with gasoline, diesel, kerosene, jet fuel, heptane, and mineral spirits (aluminum version). It comes with the UL/ATEX listing on the entire meter, not just the electronics as competing brands have.

Each meter is built to handle flow-rates between 2-35 GPM and operate in temperatures between -40 F and 176 F.

Install it where you need it, even at the end of the hose. Measure gallons, liters, quarts, pints, and ounces. For a robust meter you can depend on, choose Fill-Rite, the most trusted name in pumps and meters.

• Dry lift and siphon gas from most vehicles, boats & equipment - A must have prepper tool -See all 5 by clicking on blue lettered "GasTapper" at top of page
• Weather resistant air-tight, fume proof case with pressure release valve so that you can store it safely in a vehicle
• 12V case-mounted Automotive grade (7-10 PSI) high-lift pump with LED power indicator and plug for cord disconnect
• 8’ coils of 3/8” FuelFlex 65, 6' 1/4 line, fuel filter, 12V auto pwr plug, in-line switch 15' 12V cord
• 2014 SEMA new products award winner! Built in the USA with US and imported parts - IMPORTANT NOTE: can not be used with 110V AC to DC convertors like automotive battery chargers. This unit has a circuit board inside and requires a computer grade 110V to 12V convertor. Motor will make noise but will not pump.

User questions & answers

Question:	Would I be able to set my gas can on the ground and have this pump gas into my car's gas tank, or would I have to hold my can level with the tank
Answer:	Don't see why you wouldn't be able to pump gas from can on ground into your gas tank. In my case gasoline was pumped up a little over 2 1/2 feet, so I don't see why it wouldn't work in your case. Might be easier on the pump to first get it started by holding the can off the ground then put it on the ground. Pump does work good and 'seems' to be a decent product. I've only had to use it twice and it worked well in both cases.
Question:	Will this work on a Trailblazer
Answer:	While we don't have any test results with the Trailblazer, the GasTapper has been used successfully in most GM vehicles of that era (2001-2009). We can guide you further over the phone to answer specific questions and/or to offer some tips on using the GasTapper with your Trailblazer. Dave---
Question:	Does this work on a 2009 Lexus RX
Answer:	Should work on any car. I love mine.
Question:	Will this work to pull motor oil out from the dipstick tube
Answer:	Hi Greg, it has been done but the 1/4 line makes it slow. OIL MUST be fully warm. Viscosity is key. Flush with kerosene when done.

Product features

GasTapper 12 Volt Standard Fuel Transfer Pump

The GasTapper 12V Fuel Transfer Pump comes with useful features to help you get the job done. It works on many cars*, boats, RVs, UTVs, as well as a variety of other fuel vessels.

Portability

It's great to always be prepared for the unexpected. That's why we house our transfer pumps in top of the line fume & weather proof cases that are both portable & durable.

Safety

We want our customers to have ease of mind and the ability to get a job done cleanly and effectively. Now you can transfer fuel without spilling or tasting it!

Patented Hose Man Clip

• Secure the Hose to a Variety of Containers to Prevent Spilage
• USA Made and Certified Fuel Grade Hose

Standard Case

• Weather Proof
• Fume Proof
• Lightweight

Power Cord and Filter w/ Screen

• 15' Power Cord w/ Power Switch
• 12V Cigarette Lighter Adapter & Accessory Plug Adapter
• Built In Filter

Fuel Funnel

• USA Made
• Standard Gas Tank Sized Mouth
• Further Prevents Spills

• Fuel Loss Prevention system automatically senses over filling with buzzer notification
• Flow Rate of 2.4 Gallons per Minute with 2 AA Batteries (NOT INCLUDED)
• Intake Tube length of 15.5 inches with a Total length of 21 inches
• Compatible with a various liquids such as any non-corrosive liquid, gas, diesel, kerosene and water (Not for drinking)
• CSA Certified under UL Standards. This product was tested by CSA per an agreement with UL, and is certified for use in both Canada and the US according to applicable Canadian and US standards

User questions & answers

Question:	Will it work for hydraulic oil
Answer:	This pump is rated for diesel and kerosene. The engine/motor oil or hydraulic fluid which has a high viscosity can not be used with this pump. Gasoline and other chemical liquids are strictly prohibited.

Product features

Battery Powered Liquid Transfer Pump

Applicable Liquids: Any non-corrosive liquids such as gas, diesel, and water (DO NOT use for drinking water)

Delivery Volume: 9 Liters per Minute

Power: Two "AA" Batteries (Not Included)

Suction Tube Length: 15.5 inch

Suction Tube Diameter: 1.3 inch

Discharge Tube Length: 24 inch

• Built in Auto-Stop to prevent loss of fuel
• Fuel Loss Prevention System: Automatic sensing pump / Buzzer Warning
• Works great with Kerosene heaters
• Makes refueling generators, lawn equipment, farm equipment simple, lifting heavy gas can's to refuel your equipment will be a thing of the past

Operation Instructions:

1. Insert Two "AA" Size Batteries (Not Included)
2. Insert Suction Tube into sending Container (Gas Can or Container with Fuel)
3. Clip discharge hose to receiving end
4. Flip Power Switch to Start
5. To Stop Flow, Wait for Auto-Sensor or flip power Switch Off