12 best camco heater

Product description

Camco RV Low Pressure Gas Regulator with a 12' hose is specifically designed for use with our Olympian low pressure gas fired heaters, the Wave 3, 6 or 8 catalytic safety heaters and on propane gas grills that have a 3/8" male flare connection. Installs quickly and easily and replaces damaged hoses and regulators. Fits all type-1 propane cylinders and has excess flow protection for your safety. The hose is a type-1 Acme connection x 3/8" female flare swivel nut. Rated at 70000 BTU per hour.

• For use with Camco's Olympian low pressure gas fired heaters
• Excess flow and thermal protection for your safety
• Rated at 70000 BTUs per hour
• Installs quickly and easily
• Type-1 Acme connection x 3/8" female flare swivel nut

User questions & answers

Question:	What parts will i need to hook-up this 57282 hose to my baby q weber grill? I have the quick disconnect and valve on my motorhome
Answer:	If your grill has a regulator on it, you will probably have to remove it and replace it with a male quick disconnect fitting to receive the female end of the hose. There are quite a few links on line that discuss this procedure and the parts required. I suggest you check them and the Weber owners site first to ensure that the hose will work with your application.
Question:	I have a quick connect outside my travel trailer. Will this work with a Camp Chef Weekender 2 Burner Stove
Answer:	Andrew,If the quick connect is standard fitting it will connect to your trailer. I'm not familiar with the Camp Chef Weekender 2 burner stove. If the camp stove does not have a male style quick connect you will need to buy it to connect to the 2 burner stove. I did it backwards I orderd the hose made sure it fit into trailer then you will need a male thread on type which thread type you will have to match what is on the Camco 5782 female side to your Camp Chef 2 burner. I hope I was helpful.
Question:	Does the f quick disconnect unscrew from the hose
Answer:	Any updates? Can the female quick disconnect can be removed from the hose?
Question:	is this 1/4" or 3/8" hose & fittings
Answer:	It looks like it has 1/4 NPT on the fitting screwing into the female quick connect. I would say 1/4 hose the OD is about 1/2"

Product description

Features. Color - Black. Fits olympian wave 3 6 and 8 heaters. Universal fit. Easy to install

• Color - Black
• Fits olympian wave 3, 6 and 8 heaters
• Universal fit
• Easy to install
• Package Quantity: 1

User questions & answers

Question:	What are the measurements
Answer:	From Front to back is 12-3/4 “ each. 1” wide each. Front is raised about 1.5 “. Mine came as a pair.
Question:	What size screws hold the legs to the heater
Answer:	Screws come with the legs as they are made specifically for the heaters 3, 6 or 8.
Question:	What size screws hold the legs to the heater
Answer:	Mine came with the correct screws: 1/8” diameter by 1/2” length. Machine thread, Phillips head.

Product description

Features. No flame flue or chimney. No electrical drain or battery connection make it the ideal solution for boon docking and dry camping. Silent operation - No fan or blower noise. Self-generating piezo starter. 100 safety shut-off valve. Use inside RV as portable unit or permanently mounted. Can also be used outdoors as portable unit. Safe for operation at altitudes up to 12000 feet. Adjustable from 3200 to 6000 btuhr. Will heat up to 230 sq. Ft.. For use in vented areas only

• No flame, flue or chimney
• No electrical drain or battery connection make it the ideal solution for boon docking and dry camping
• Silent operation - No fan or blower noise
• Self-generating piezo starter
• 100% safety shut-off valve

User questions & answers

Question:	Will this run on a 20 lb propane tank? I need a unit for my home when the power goes out
Answer:	Yes, that's what we use. We have two Wave 6 heaters and a Wave 3 in our van conversion. We use a 12lb propane cylinder in the van.
Question:	How much water vapor does this unit create
Answer:	I live in the desert Southwest, so there generally isn't any except a small amount of condensation on the windows-maybe. When it rains, there is still just a negligible amount. Back East or in more humid climes, I imagine there could be more.
Question:	suggestion for hose please, need to connect to my existing gas line inside my trailer. I pulled the old furnace out, so have copper pipe connection TY
Answer:	Hey Nick. I used a regular flexible LP gas line that I had originally made for an auxiliary propane bottle. Whatever you use, make sure it's rated for Liquid propane. The Wave website can supply you with the fitting sizes for the heater if you need them. I don't remember them off the top of my head. We installed 3 of these in our coach and they are great heaters. HTH
Question:	How can I connect this unit to a disposable 1-lb propane cannister
Answer:	You don't.

Product description

Camco RV 90 degree Elbow Connector is specifically designed for use with our Olympian low pressure gas fired heaters. Perfect for use with the Wave 3, 6 or 8 catalytic safety heaters. The elbow is able to swivel 360 degrees to provide easy installation. It has a 3/8" female swivel flare x 3/8" male flare.

• For use with Camco's Olympian low pressure gas fired heaters
• 3/8" female swivel flare x 3/8" male flare
• Swivels 360 degrees
• Installs quickly and easily
• Perfect to use with our Wave 3, 6 and 8 catalytic heaters

User questions & answers

Question:	should i use some gas line pipe thread tap when installing it on the heater
Answer:	No, tape is not necessary as this is a flare fitting. This may be obvious but... when installing make sure you have the proper alignment of the elbow before tightening. This is a "fixed 90" once tightened, not a swivel as it may appear.
Question:	Will this swivel even after the fitting is tightened down? Looking to mount Wave 3 on wall and allow it to swivel off the wall while connected. Thanks
Answer:	Once the fitting is tightened down, it does not swivel.
Question:	Will this work on propane grills, too
Answer:	That would depend on the grill, if you're grill has this type and size of a flared fitting, then yes.
Question:	I just ordered a camco wave 3 heater. Is this part necessary? Thanks
Answer:	Makes it a lot easier to connect a propane line and control the angle it comes into the heater. The alternative is multiple connectors to do what this one connector does.

Product description

The most popular element in use today. Fits Private Label, State, Reliance , Rheem, Ruud, Sears, Montgomery Ward, and many other brands. Elements individually carded.

• High Watt Density heating element
• 120V/1500W
• UL Listed
• Minimum tank diameter 9"
• Sold as 2 Pack

User questions & answers

Question:	Does this fit into a surburban RV water heater
Answer:	It 4 by 2 1/2 and yes can hold a business card even a credit card
Question:	Is this for two
Answer:	Yes,These pants are to the ankle.

Product description

Cameo's 9000 with 240V Screw-In Type High Watt Density Thankless Water Heater Element is a universal replacement for Eco Smart electric thankless water heaters. This element is compatible with Eco 18, Eco 27, and Eco 36 models. They are easy to install and come with detailed instructions on how to replace your old element. The replacement element must be the same voltage and wattage as the element being replaced. Never exceed the nameplate rating on the water heater.

• Wattage/Voltage: 9000with240V; 2300with120V
• Style: Screw-in fold back
• Construction: 1-inch NPS brass bushing with copper sheath; Includes gasket
• Compatibility: Thankless water heaters - Eco 18, Eco 27, and Eco 36 models
• : 1-year limited

User questions & answers

Question:	What is the actual product dimensions and not the package dimensions
Answer:	Since, I was replacing an burnt out element, in a EcoSmart 36 tankless heater, I did not measure it. I purchased this element which fits several of the EcoSmart heaters (of which the 36 was listed). I knew it would fit and there were not problems. Sorry I don't have more information.
Question:	Will this work with a richmond rmtex-27kw
Answer:	Compatibility: Tankless water heaters - Eco 18, Eco 27, and Eco 36 models
Question:	Will this element fit in a eemax em24027 model
Answer:	Item# 02133 replaces elements in EcoSmart models ECO 18, ECO 27, & ECO 36 models, which are whole-house units with a 9,000W (9kw) / 240 V element. They are not made to replace elements in the Eemax EM models. Any replacement element should have the exact same wattage and voltage as the OEM element and be made specifically for Tankless units.
Question:	what country is this manufactured in
Answer:	Vietnam

Product description

With the RV Hot Water Heater you can convert your gas unit into an electric one and save the propane for your barbecue. It converts any 6-gallon RV LP gas water heater to 120 volts of electricity on demand and has a stainless steel cartridge that heats the water to temperatures ranging from 90 to 150 degrees Fahrenheit. This water heater conversion kit includes an on/off power switch with a mounting bracket and a fully adjustable thermostat for both convenience and safety. A 15 A/120 V electrical service is required to use this water heater, which includes a kit with all necessary power cords and color-coded wire assemblies to make setup quick and easy. This 6 gal RV water heater's thermostat comes factory preset to 120 degrees Fahrenheit and might require adjustment, depending on your system.

• Converts any RV LP gas water heater to 120v electricity on demand
• Includes on/off power switch with mounting bracket and fully adjustable thermostat
• All necessary power cords and color-coded wire assemblies are included
• For 6 Gallon RV water heaters
• 425W element measures 6.25” long

User questions & answers

Question:	How many watts is the heating element
Answer:	It is only about two feet from the base. It runs the length of the lamp, but only a short amount comes out from the base.
Question:	Is there any reason I could not control this with a different thermostat? I want to heat water in a tub
Answer:	There very sturdy not had any issues whatsoever.
Question:	can I still use the existing propane at the same time as the electric for quicker heat up
Answer:	Yes, the heating lamps can be replaced.
Question:	Watts
Answer:	It provides warmth to the people sitting directly under it, and I would say within 5 feet and that’s about it. We are using it for our patio for a 6 ft long table, and it does not reach people at the other end.

Product features

Camco Hot Water Hybrid Heat Kit (11673)

Camco 6 Gallon RV Hot Water Hybrid Heat easily converts any 6-gallon RV LP gas water heater to 120V electricity on demand, helping to conserve propane. Its stainless steel heating cartridge heats the water to temperatures ranging from 90° to 150° F. The kit includes On/Off power switch with mounting bracket and fully adjustable thermostat. All necessary power cords and color-coded wire assemblies are also included. 15 A/120 V electrical service is required for use. The thermostat is factory preset to 120° F.

Product description

Camco's RV Water Heater Tank Rinser helps extend the life of your water heater. The rinser lifts sediment that collects at the bottom of your hot water heater and washes it out of your water heater tank. Just hook a garden hose to the rinser and insert it into the water heater drain. The rinser has a shut off valve as well.

• Cleans sediment out of RV hot water heater
• Attach garden hose and insert into drain opening
• Includes shut off valve
• Helps extend the life of your water heater
• Lifts sediment that collects at the bottom of your water heater
• Cleans sediment out of RV hot water heater
• Includes shut off valve

User questions & answers

Question:	What is the diameter of the tip
Answer:	No. This one is propane only, no electric.
Question:	What is the tube made out of? Plastic? Metal
Answer:	No, it has a pilot light that is on all the time.
Question:	Will this work with suburban hot water heater
Answer:	Yes it is propane
Question:	I'm new to RVing. Could the same be done with a garden hose? I have a Suburban suburban SW6D-type
Answer:	It goes in a camper. Water comes from water source and fills this tank. The water is heated by gas or electric. When you turn one of your faucets on that’s the pressure source.

Product description

Camco's drain plug wrench is specifically designed for use with RV water heater drain plugs. The angled design conveniently fits in tight spaces and includes prongs for rusted drain valves and petcock drains. Fits both 7/8" and 15/16"Drain plugs. Includes two 1/2" NPT replacement drain plugs and Teflon tape.

• Designed for RV water heater drain plugs
• Fits both 7/8" and 15/16" drain plugs
• Angled design allows you to reach tight places
• Includes prongs for rusted drain valves and petcock drains
• Includes wrench, two 1/2" NPT replacement plugs and Teflon tape

User questions & answers

Question:	Is this a direct replacement for
Answer:	These plugs are hollow and it leaked after a the water heater cycled a few times. I replaced with Atwood plugs and no problems since.
Question:	how long is the wrench
Answer:	No it's the same plug that came with my rv new.
Question:	Are these plugs hollow, or solid plastic
Answer:	For use with hand drive roofing nails. Shoots loose nails into tight spaces. Used for installing ridge vent, vinyl siding and under eaves. Features: One third the size and weight of standard palm nailers Lightweight and compact Easily fits into nail pouch Magnetic nose holds fastener Easy to actuate Nail seats deeply for easy use Prevents damage from missed hammer blows Specifications: Firing Mode: Multi-blow Operating Pressure: 60-110 PSI Fastener Type: Hand drive roofing nails Fastener Range: 7/8" to 3" Height: 2.8" Length: 4.0" Width: 2.2" Weight: 1.0 lb.
Question:	What is the insect resistant plug? (I'm guessing its vented for off season storage, not usable when using the RV
Answer:	Hold it in place longer to drive the nail in farther. It's basically a pneumatic hammer. It doesn't drive the nail in one single action. This was a lifesaver for nailing shingles under a low clearance eave.

Product features

Camco RV Water Heater Drain Plug and Wrench Kit

Description:

Camco's drain plug wrench is specifically designed for use with RV water heater drain plugs. The angled design conveniently fits in tight spaces and includes prongs for rusted drain valves and petcock drains. Fits both 7/8" and 15/16"Drain plugs. Includes two 1/2" NPT replacement drain plugs and Teflon tape.

• Designed for RV water heater drain plugs
• Fits both 7/8" and 15/16" drain plugs
• Angled design allows you to reach tight places
• Includes prongs for rusted drain valves and petcock drains
• Includes wrench, two 1/2" NPT replacement plugs and Teflon tape

Product description

Camco's all-stainless water heater elements are made from a high performance nickel-chromium stainless alloy. The bushing is also stainless steel to prevent rusting when exposed to moisture. These Premium ultra low Watt density elements also help prevent caramelizing and scorching when used in Electric home brewing applications.

• All-stainless element will not rust
• Helps prevent scorching & caramelizing when used for electric brewing applications
• 1" NPSM Threads
• Resists dry-firing (warranty is void if element is dry-fired)
• 1Yr limited warranty when used in brewing applications (or in any application outside of normal residential water heater use) and 5-yr limited warranty for normal residential water heater applications

User questions & answers

Question:	how hot will this make a 33 gallon tank
Answer:	It will make it as hot as you want - just a matter of how long it will take.
Question:	What is the length (Overall and/or Element) of the Camco
Answer:	I'd have to measure, but 10", i think. Also, threads are straight, not tapered, as a typical water heater element is.
Question:	I see the review of someone having been sent 3 broken elements. Has anyone had a successful purchase experience here
Answer:	I bought two 02964/02965 elements and they both arrived in one piece. They arrived in their individual Camco boxes within a bigger box. It might have helped that nothing else was packed with them.
Question:	What is the insert length, camco 02934 stainless steel water heater element (5500w 240v
Answer:	Approximately 11.75” once you deduct the length of the bushing/threads.

Product description

Places gas water heaters 18" above floor as reqired by the National Fuel Gas, and Plumbing Codes. 18 gauge galvanized sheet metal holds up to 50 gallon water heaters. For use with gas water heaters having a diameter of 22" or less and a rated capacity up to and including a 50 gallon water heater. Easy instructions. 21" x 21" x 18"

From the Manufacturer

The Camco gas water heater stand is used when local building codes require a water heater stand for gas water heaters located in areas where the accumulation of combustible fumes may occur.

• Minimal assembly required
• 21" x 21" x 18"
• Constructed of galvanized steel
• Fits up to a 50 gallon water heater
• For use with most residential water heaters

User questions & answers

Question:	Does this stand have to be assembled
Answer:	Yes. Comes in a flat box. Very easy to assemble.
Question:	Can this stand be spray painted
Answer:	If you clean it first with the alcohol then use a good primer you can paint it my question to you is why would you paint it it’s all stainless steel.
Question:	Is there any way to attach the stand to a floor
Answer:	Sorry -no it is not designed to be bolted to floor. Any other questions, please feel free to call us at 800-334-2004 Monday - Friday 8am to 5pm EST. Pick the hardware option.
Question:	Does the top shelf area measure 21 x 21? Most of these are 22 and I need 21 so I can open the closet door
Answer:	I just measured the assembled stand; it is 21-1/4" x 21-1/4". The stand itself is 21" x 21" but the bolts fastening the shelf to the frame stick out 1/8" on each side.

Product description

The Camco Water Heater Element Quick Change Tool helps you save time and water when changing your water heater element. Instead of emptying your entire water heater tank just to change the element, simply turn off the water at the water heater to create a vacuum. Securely attach the tool, and place a bucket handle in the built-in groove to catch any excess water. Quickly change the element and remove the tool when you’re done. The Water Heater Element Quick Change Tool is simple and easy to use, and made in the USA.

• Helps save time and water when changing your water heater element
• Eliminates the need to drain you water heater tank
• Built-in groove holds a pail or bucket to catch water
• Simple and easy to use
• Made in the USA

User questions & answers

Question:	How does this attach
Answer:	On my water heater, the elements had a 'bump' where the tank was threaded that the ring sort of jam-fit onto. (I found it easiest to do it by putting the top center of the ring on the top of the bump then pressing down using the spout as a lever).